How to Install a Grab Bar in a Fiberglass Shower

Do you want How to Install a Grab Bar in a Fiberglass Shower? Are you searching for the answer on how to install a grab bar in a fiberglass shower?

You are surfing on the right platform to have an efficient answer.

Look: A grab bar in the shower is potential support for the weak and physically disabled person.

What is it now?

Install a grab bar in a fiberglass shower right now.

Installing a grab bar in a fiberglass shower may force you to crack the fiberglass. To avoid an accident, read the instructions attentively.

Listen: I have enclosed the efficient, easy, and safe way to install a grab bar in your fiberglass toilet.

How Much Does it Cost to Install a Grab Bar in Shower?

Are you focusing on universal design and want a home you can age?

Grab bars are the perfect addition to your system.

Grab bars can help you get lower onto your toilet or shower bench; moreover, if you are in a wheelchair or a walker, it can quickly help you get to the shower or the bath. Almost everyone in your house can benefit from it; however, those who have mobility based disability in your place can be greatly benefited from this.

A grab bar can generally cost you from 85 dollars to up-to 300 dollars for installation; moreover, average you can install steel L-shaped bars for around 243 dollars.

Average cost- $243.

Average range – $85 – $300.

At maximum, it can cost you up to 337 dollars.

What do you need to install a grab bar in fiberglass?

Arrange the tools below from your local market.

  • Pencil
  • Drill
  • Painters tape
  • Stud finder
  • Two-inch hole saw
  • 1/8 inch drill bit
  • 3/16 inch drill bit
  • Utility knife
  • Socket wrench
  • Fiberglass grab bar
  • Screwdriver
  • Silicone caulk

How to install a grab bar in a fiberglass shower: Step by Step Process

Step 1: Locate a stud-

stand near the shower and measure the height of 33 inches from the floor. Find a stud there.

You have to locate the center of the stud and use the low tack painter’s tape to mark the targeted place.

Make sure you have marked the right place to install the bar.

How to Install a Grab Bar in a Fiberglass Shower

 Step 2: Put the painters’ tape across the wall-

After locating the right place, fix the low tack painter’s tape across the wall.

Be careful that you are marking the place sitting in the tub. Here, you have to judge the suitability of the bar so that you can grab the bar easily.

Step 3: Hold the bars on the wall-

Here, you have to measure the distance of the two bars with the drilling position.

Hold a bar in one corner following the tape that you have marked on the stud.

In the same way, hold the second bar in the right position.

You have to trace the perimeter between the two bars.

Step 4: Mark the holes-

 Holding the bar in the right place, you have to mark the dots.

Be careful when you are marking the dots. The dots are the indicator where to make holes.

You can use a pencil to trace the circles and marks.

Step 5: Drill 1/8 inch-

Take the drill machine at the dots that you have marked a few minutes ago. Make a 1/8 inch hole.

Now insert a nail or anything like that to be sure the hole is over a stud.

Step 6: Make a 2-inch hole-

It is time to make a hole into the fiberglass. Look at the shower we have traced circles.

Make a 2-inch hole with a 2-inch hole saw.

Do not go deeper exceeding the actual measurement of the hole.

Step 7: Cut the grab bar-

Now, measure the space between the stud and the surface of the fiberglass wall.

Here, we have to cut the grab bar mounting spaces so that the grab bar can get a suitable place.

Use the utility knife to cut the grab bar to that length.

Step 8: Drill of the pilot hole-

Take the drill machine again and put it on the stud. Make a pilot hole with a 3/16 inch drill bit.

Make a hole in each stud. Now, place the pilot hole on the stud and the 2-inch hole in the fiberglass.

Do not force the fiberglass harder. It may crack.

 

How to Install a Grab Bar in a Fiberglass Shower

Step 9: Tight the bolt and the pilot hole-

Find the lag bolt and the washer. Insert them into the mounting spacers.

Find the mounting lag bolt assembly into the pilot hole attentively. Now push the bolt into the stud using a socket wrench.

Twist the wrench until it is tight enough.

Step 10: Run silicone caulk-

Take the silicone caulk in your hand. Pour a bit of silicone caulk around each hole in the fiberglass.

Try to bead a good amount of caulk so that it can block the unnecessary holes.

Step 11: Insert the mounting bracket-

Insert the mountain bracket to fix with the mounting spacer.

Get the disk sides of the bracket facing onto the spacer so that we can put the screw in the right place.

Get a screwdriver and place it on the screws. Make sure the mounting bracket disk reaches the fiberglass wall.

Put the screws in the disks.

Step 12: Adjust the holes-

Adjust the alignment between the disks and the shower wall. Check out the screws whether they are in the exact position.

The grab bar and the mounting brackets must stand in a single line. If not, shake the bar a little bit to adjust.

Finally, drive the screws through the holes using the screwdriver. Turn the screwdriver until it is tight enough.

Make sure the bar is in the right position on your shower wall. Set the other one in this way.

How to Install a Grab Bar in a Fiberglass Shower Video

Final step:

 Grab the bar and push it. Try to feel any disorder in the bar or the shower wall.

If everything is fine, wash out the shower with fresh water.

Also, Read – How to Clean Fiberglass Shower 

Cautions: 

Do not try to do this job faster. Remember that you are working with fiberglass.

Arrange the things from the list above at first.

If possible, take help from experts or someone else who has done this job already.

When you are drilling holes, do not push the machine strongly. It may break the glass.

Cover the working area with soft cloths so that you cannot harm the floor.

Do not forget to wear hand gloves.

Bottom line:

You cannot be an expert installing the grab bar following those instructions. However, you can accomplish the job at your shower following the instructions.

You have the instructions in the article. Now, it is your beauty to cope up with the guidance of how to install a grab bar in a fiberglass shower.

I hope, you will do your best to set up a bar perfectly in your shower.

4.1/5 - (285 votes)
Spread the love

SARA PEARSON

Hi, Sara here. Before ending up as a professional hair care expert and beautician, I was quite obsessed with the hair and skincare of myself. While turning myself devoted to what I love, I came up with the idea of sharing the advice and tips with you lovely people as well. Hence, here goes my little corner on the web where we talk about health, hair, and more!

Leave a Reply

Your email address will not be published. Required fields are marked *

Next Post

Difference Between Angle Grinder vs Soldering Iron

Tue May 11 , 2021
Have you used an angle grinder or soldering iron? If the answer is “Yes”, you might know the difference between anger grinder vs soldering iron. To make you more clear about these two tools, I have discussed the comparison between these two stationary tools in detail. Already you have seen […]
Difference Between Angle Grinder vs Soldering Iron

All Categories